EverFocus EDN800 Uživatelský manuál

c EDN800 User’s Manual Copyright © EverFocus Electronics Corp, Release: Dec. 2009 Rev.C

EDN800 10 3. Setting Click this button to display the setup menu. 3.1 System Info System information and system log check of the setu

EDN800 113.1.1 Information System Information: Firmware version, MAC address, Video Type, Model number. (unchangeable, for reference only) 3

EDN800 12 System Log: Date/Time: displaying date and time of the log. Log message: all information and event message, including login, user’s

EDN800 13 Text Setting Check the box for text of Machine name, Date/Time or Frame Rate to be displayed on the screen. Text Color Foreground Col

EDN800 14Time Format: 24 Hours or 12 Hours. Press Apply to apply the setting changes or Reset to reset without saving the change. Recording/Snap

EDN800 153.3 Network The network settings and the settings relating to Network, DDNS, Bandwidth, SMTP/FTP and Network Alarm can be configured on t

EDN800 16DHCP: Configure the DHCP server not to assign the same IP addresses used for the other network cameras and PCs whose IP address is unique

EDN800 17Press Apply to apply the setting changes or Reset to reset without saving the change. Port Setting HTTP Port Port number for HTTP/WEB c

EDN800 18○ www.dyndns.com ○ www.no-ip.com Enable: Check the box to enable DDNS setting. Service ISP: If you choose EverFocus DDNS server, you

EDN800 19 Bandwidth Setting Max. Bandwidth: Specify, Unlimited / 64 K/ 128 K/ 256 K / 512 K / 1M / 2M / 4M / 8M bps. the maximum bandwidth that th

- - 2Product Name: EDN800 EverFocus IP Network Cameras Model Number(s): EDN800 FCC Notice "Declaration of Conformity Information" This equ

EDN800 20 Set SMTP The settings relating to the mail server used to send the e-mail notification from the camera to predefined addresses via SMTP

EDN800 21Send Test Mail: Press button to send a testing mail to the assigned address. Set FTP The settings relating to the FTP server used to

EDN800 223.3.5 Network Alarm (reserved for PowerCon) Set Network Alarm This function is reserved for PowerCon software, for the detail setting p

EDN800 233.4 Video The settings relating video such as streaming, camera OSD can be configured on this page. The "Video" page has 2 tabs

EDN800 24Quality: there are 8 types of quality, please choose from Highest / Higher / High / Middle / Normal / Low / Lower / Lowest. Frame Rate:

EDN800 253.4.2 Camera Camera Settings The "Camera OSD setting" can be displayed on a video monitor and can be configured using the ope

EDN800 26 brightness of the screen. OFF: Disable electronic shutter. BLC: Select ON or OFF for Backlight Compensation. ON: When the backgro

EDN800 273.5 USER User Information Maximum 10 users can be set for using the IP camera. The user information displays the authorized users and a

EDN800 283.6 EVENT An event in the camera is when an Event Type is activated and causes certain actions to be performed. The event type is the set

EDN800 293.6.1 Event The settings relating to event occurrences such as settings for the event occurrence, motion, alarm and time mask can be conf

- - 3About this document All the safety and operating instructions should be read and followed before the unit is operated. This manual should be ret

EDN800 30 or button to move between events. The event that has highest priority will be activated first. Press Apply to apply the setting chan

EDN800 31post alarm buffer setting, please refer to “3.6.3 Alarm”. 6. Check “Enable This Event”. 7. Select “Always” for time mask. For detail ab

EDN800 32There are 5 motion trigger areas, which can be distinguished by 5 different colors. Check Enable checkbox to enable event action. For eac

EDN800 33set up to 120 seconds. Post-Alarm Buffer: Image saved internally in the server from the time immediately after the trigger. Input the des

EDN800 34Mask name: Input a mask name for the new time period. Check the check box for the day to be scheduled: Sun, Mon, Tue, Wed, Thu, Fri &

EDN800 353.7.1 Date/Time Machine Name Setting Machine Name: Enter the name of the camera. The entered name will be displayed in the status displ

EDN800 36value and down arrow to decrease value. Press Apply to apply the setting changes or Reset to reset without saving the change. Set Date/

EDN800 373.7.2 Daylight Saving Set Daylight Saving Check Enable Daylight Saving checkbox to enable daylight saving. Set the start time to day

EDN800 38 Press Apply to apply the setting changes or Reset to reset without saving the change. 3.7.3 SD Card Setup SD Card Notification: Notif

EDN800 39record event video to SD card. Overwrite: Select ON for overwriting data when SD card memory is full. Select OFF for not overwriting SD c

- - 4 Use only the recommended power supplies. Power supplies must comply with the requirement of the latest version of IEC60950-1. Substitutions m

EDN800 403.7.4 Maintenance Maintenance Server Reboot: The unit is rebooted without changing any of the settings. Use this method by pressing Reb

EDN800 41the Load button. The settings will be restored to the previous configuration. Upgrade Firmware Upgrade the EDN800 with the latest firm

EDN800 424. SPECIFICATIONS CAMERA Pickup Device 1/3" Sony Super HAD Interlaced CCD Picture Elements NTSC: 768 (H) x 494 (V); PAL: 752 (H) x

EDN800 43 EverFocus Electronics Corp. Head Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886-2-26982334 FAX: +886-2

- - 5TABLE OF CONTENTS 1. INTRODUCTION...6 2. FEATUR

- - 61. INTRODUCTION The EDN800 vandal dome network camera provides H.264, MPEG-4 and MJPEG compression for multi-streaming capabilities. H.264 is th

3. OPERATION WINDOW Step 1.Start a browser. Step 2. Enter the IP address or host name of the camera in the Location/Address field of your browser. Ste

EDN800 8○3 Press button to close EDN800 network page. ○4 Video Stream Select Video Stream from Stream 1 / Stream 2, Stream 3 and Stream 4. Pl

EDN800 9The Snapshot button saves a snapshot of the video image currently being displayed. The location where the snapshot data is saved can be sp