EverFocus NVR Uživatelský manuál Strana 1

NVR 8004X 4CH / 8CH / 16CH Tower NVR with 4HDD Bays User’s Manua

NVR8004X 3 1.3 Packing List • NVR x 1 • Quick Guide x 1 • CD x 1 *see note 3 • Mouse x 1

NVR8004X 93 Typical D-Link Port Forwarding This section will cover a few simple configurations for

NVR8004X 94 Click Virtual Servers on the left to bring up the following screen. Virtual Servers

EverFocus Electronics Corp. EverFocus Taiwan: 12F, No.79, Sec. 1, Shin-Tai Wu Road, Hsi-Chih, Taipei,

NVR8004X 4 1.5 Front Panel 1234 Figure 1-2 Note: For example, if the HDD1 is installed befor

NVR8004X 5 1.6 Rear Panel 1345726 Figure 1-3 No. Name Description 1 Reset Insert a tool int

NVR8004X 6 2. Installation 2.1 Hard Disk Drive Installation 1. Make sure the NVR is power-off

NVR8004X 7 4. Insert 2.5” or 3.5” HDD in the tray. HDD Tray Figure 2-3 5. Secure the HDD with th

NVR8004X 8 7. Close the locking arm until you hear a click. Figure 2-7 8. Close the cover of t

NVR8004X 9 2.2 Basic Connection The instructions below describe the connection for the NVR8004X.

NVR8004X 10 2.3 USB Dongle Connection Please connect your USB Dongle before powering on the NVR.

NVR8004X 11 2.5 Connecting the NVR to the Network There are three methods to connect the NVR t

NVR8004X 12 Connection Procedure:  The First step is to purchase or make a straight through cabl

EVERFOCUS ELECTRONICS CORPORATION NVR8004X User’s Manual  2013 EverFocus Electronics Corp www.everfocus.com All rights reserved. No part

NVR8004X 13  Take the values for Subnet Mask and Default Gateway and input them into the NVR; th

NVR8004X 14 2.5.2 Direct High-Speed Connection In a Direct High-Speed Connection, the NVR connect

NVR8004X 15 2.5.3 One-to-One Connection You can connect directly without using a switch, router o

NVR8004X 16  Go to Start. Double-click on Control Panel. Figure 2-14  Click Network and Int

NVR8004X 17  Right-click on Local Area Connection and select Properties. Figure 2-17  Click

NVR8004X 18  To access the NVR from the computer, simply open Internet Explorer and in the addre

NVR8004X 19 2.6 Checking the Dynamic IP Address You can look up the IP address and access the Web

NVR8004X 20 4. Type the user ID and password. Click OK. Note: 1. The default user ID is admin a

NVR8004X 21 9. When first connecting to the NVR’s IP address, the following dialog may appear. Ple

NVR8004X 22 3. Remote Access to the NVR 3.1 Accessing the NVR Follow the steps below to access

ii Warranty Based on the RMA policy, EverFocus Electronics Corporation ("EverFocus") will repair or replace, at no charge to the purchaser

NVR8004X 23 3. You might be required to download ActiveX and JAVA software for viewing the camera

NVR8004X 24 3.2 Installing JAVA Runtime You need to install the latest JAVA software for stab

NVR8004X 25 3.3 Browser Security Setting 3.3.1 Installing ActiveX Controls Follow the steps be

NVR8004X 26 3.3.2 Enabling ActiveX Controls Note this section is only necessary if you DO NOT see

NVR8004X 27 3. In the Security Settings window, scroll to “ActiveX controls and plug-ins”. Figur

NVR8004X 28 5. Close the window so you are back at the login screen. 6. Click the Refresh button

NVR8004X 29 4. Remote Live View and Configuration Live View: 2345176 Figure 4-1 No. Name Descri

NVR8004X 30 5 Channel Buttons Click on the number to display the channel in full screen. 6 Stat

NVR8004X 31 4.1 Camera Users can automatically search and add the cameras in the Auto Search sett

NVR8004X 32 4.1.2 Add Camera Manually You can also add the IP camera manually by typing its IP A

iii  Read Instructions All the safety and operating instructions should be read before the unit is operated.  Retain Instructions The safety

NVR8004X 33 To successfully add the IP camera, you need to click the Save button in this page. You

NVR8004X 34 4.1.3 Advanced Setting The Advanced Setting is for users to view, add, delete or modi

NVR8004X 35 4.1.4 Camera Setting Users can configure the detailed camera settings, PTZ and track

NVR8004X 36 Hallway Mode (9:16): The option only appears when the selected camera is equipped with

NVR8004X 37 4.1.4.2 PTZ You can set up the Preset, Auto Pan, Tracking, Pattern and Tour setting

NVR8004X 38 Preset: Click the Preset button to set up the Preset Position or the Auto Pan function

NVR8004X 39 Auto Pan: You can only configure one Auto Pan sequence. The configured Auto Pan (A to

NVR8004X 40 Tracking: Click the Tracking button to set up the tracking function which is functiona

NVR8004X 41 Note: Please note that if enabling the Pan/Tilt Limits function, the position of the S

NVR8004X 42 Pattern Tour: Figure 4-13 Pattern: You are given 90 seconds to move the camera (via

iv This Product is RoHS compliant. ATTENTION! This is a class A product which may cause radio interference in

NVR8004X 43 Tour: You can combine up to 16 preconfigured camera positions and patterns into one lo

NVR8004X 44 4.2 Record You can configure the basic recording settings on the hard disk. Figure 4

NVR8004X 45 4.3 Event 4.3.1 Disconnect You can enable the Disconnect Event function and configur

NVR8004X 46 4.3.2 Motion You can enable the Motion Event function and configured the related

NVR8004X 47 To Edit the Motion Grids: 1. Click the Edit Motion Grid button, the Motion Setting me

NVR8004X 48 4.3.3 Other You can configure the event settings and enable the Buzzer or Email alert

NVR8004X 49 4.3.3.2 Disk Failure Figure 4-20 Log: Check the box to record alarm events to log

NVR8004X 50 4.3.3.4 Disk Off Figure 4-22 Email Notify: Check the box to send email notificatio

NVR8004X 51 4.3.3.6 Network Loss Figure 4-24 Log: Check the box to record alarm events to log

NVR8004X 52 4.4 Hard Disk The Disk menu is used to review the NVR’s hard drive settings and statu

v TABLE OF CONTENTS 1. Introduction ...

NVR8004X 53 4.4.2 Lock / Format You can control the percentage of the hard disk space reserved fo

NVR8004X 54 4.5 Network The NVR allows you to use a Web browser to remotely view and manage the s

NVR8004X 55 Subnet Mask: Displays the subnet mask for your network so the NVR will be recognized w

NVR8004X 56 obtain a list of the IP addresses of their recommendation of the best servers to use f

NVR8004X 57 4.5.2 Email Figure 4-28 SMTP Server: Assign the SMTP (e-mail) server’s name. Note t

NVR8004X 58 4.5.3 DDNS DDNS (Dynamic Domain Name System) is a service used to map a domain name t

NVR8004X 59 4.5.3.1 EverFocus DDNS Note that the DNS Server 1 (6.7.1 LAN) should be set up corr

NVR8004X 60 4.5.3.1 www.dyndns.org Figure 4-31 DDNS Service: Select www.dyndns.org from the dro

NVR8004X 61 4.5.4 FTP Set up the FTP server settings to enable the FTP function. The function is

NVR8004X 62 4.5.5 Alarm Server You can send out the alarm notifications to EverFocus’s CMS softwa

vi 4.3.2 Motion ...46 4.3.3 Other ...

NVR8004X 63 4.6 Schedule You can set up the recording schedule with the desired time, event types

NVR8004X 64 4.6.2 Holidays In addition to set up a weekly recording schedule, you can also set up

NVR8004X 65 4.6.3 Schedule You can set up the camera recording mode by time of day on specifi

NVR8004X 66 1. Select a camera first and double-click on desired start time block (no number on i

NVR8004X 67 Apply to Days: This button can be used to copy schedules to other days. Select which d

NVR8004X 68 4.7 System Setting You can configure the general settings for the NVR in this menu. 4

NVR8004X 69 4.7.2 Daylight Saving You can configure the settings for NVR to automatically adjust

NVR8004X 70 4.7.3 User Group This setting page is used for configuring the privilege of the three

NVR8004X 71 4.7.4 User Management You can create multiple user accounts (max: 20 user accounts) w

NVR8004X 72 You can further configure each user account and its settings individually, see the ste

NVR8004X 1 1. Introduction EverFocus NVR8004X is a professional standalone network video server

NVR8004X 73 Figure 4-46

NVR8004X 74 4.7.5 EKB200 You can connect an EKB200, which is EverFocus’ USB keyboard, to the

NVR8004X 75 【Key No】 The control key number on the keyboard. 【Action】 Select an item from the

NVR8004X 76 4.7.6 Miscellaneous You can upgrade the latest firmware, restore the factory default

NVR8004X 77 4.8 System Information You can see the NVR information and Log data in this menu. Or

NVR8004X 78 4.8.2 Log You can choose, display or export log data using this menu. Figure 4-51 St

NVR8004X 79 4.9 Copy 4.9.1 Copy You can archive the recordings or log data (event and motion) to

NVR8004X 80 4.9.2 Quick Archive Figure 4-54 【Configurations】 Archive Interval: Click the Archive

NVR8004X 81 4.10 Search You can search the recordings for playing back by using the Search menu.

NVR8004X 82 4.10.2 Event Search Figure 4-57 Start Date / End Date: Click to bring up the on-scre

NVR8004X 2 1.1 Overview Front ViewRear ViewInternal HDDs (Optional)KeyPower SupplyUSB3.0 USB2.0Ne

NVR8004X 83 4.11 PTZ You can use the PTZ Control Panel to control the connected PTZ cameras, to s

NVR8004X 84 7. To jump to a Preset Position: a. Click the Preset button. b. Click the desired P

NVR8004X 85 5. Specifications Model Name NVR8004X-04 NVR8004X-08 NVR8004X-16 System Operating S

NVR8004X 86 General Power Input 19 VDC, 4.74A Power Consumption 90W max. Operating Temperature 0°C

NVR8004X 87 Appendix A: Network Overview This chapter will give you a basic instruction on how to

NVR8004X 88 Gateway Address Addressees are either local or remote. A gateway address is composed o

NVR8004X 89 Pre-Installation Before beginning the installation, please answer the following questi

NVR8004X 90 Pre-Installation Everfocus’ NVR can operate using one of three types of networking con

NVR8004X 91 Appendix B: Linksys & D-Link Port Forwarding Typical Linksys Port Forwarding This

NVR8004X 92 Click on the “Applications & Gaming” tab. Applications and Gaming allows you to